Loop Minimalist Wall Light

Description

1. Hero intro

A plug-in wall sconce — no electrician needed. A small copper-finished disk mounts to the wall with two screws; a black braided cord drapes through a brass loop above and ends in an E26/E27 bulb socket below. 78.7″ cord with built-in switch plug — install in 5 minutes anywhere with a wall outlet. Ships with one test bulb so you can light it up immediately on arrival.

3. Lead USP – no electrician: ✓ No electrician, no wiring, no permission needed

This is a true plug-in wall sconce. Two small wall-anchor screws hold the brass disk; the cord runs to any standard outlet via a switch plug. Renters, apartment dwellers, dorm rooms, and anyone who cannot modify wiring — this works for you. To uninstall (when you move out), unscrew the two anchors and patch two small holes.

4. Features

Features

Plug-in install

5-minute mount with two screws + plug-in to wall outlet. No hardwiring, no junction box, no electrician.

Drape cord through loop

Black braided cord runs through a small brass loop above the disk — the loop holds the cord shape, the socket dangles at the bottom.

Test bulb included

Ships with one E26/E27 bulb pre-fitted for arrival testing. Swap to your preferred bulb anytime (LED, Edison filament, dimmable).

Finish: Copper (disk & loop)

Black braided cord

Single finish only. The copper baked-paint coat over the brass hardware reads warm and matches walnut, leather, marble, and brick interiors.

12. Specifications

Specifications

Dimensions

Ø3.1″ disk × 12.6″ total height (8 × 32 cm)

Weight: ~2.2 lbs (1 kg)

Material: Copper-finished metal disk and loop · black braided cord · brass socket housing

Light source

E26 (NA & CA) or E27 (EU/AU) — max 40W. One test bulb included; LED bulbs recommended (sold separately for replacement)

Voltage: AC 110–240V (universal)

Mounting: Two screws into wall — anchors included. No hardwiring

Cord

78.7″ (200 cm) with built-in switch plug; correct plug type ships per destination (NA/EU/AU/SA)

Control

Push-button switch on cord; dimming requires a dimmable bulb + a smart plug or switched dimmable outlet

Certification: North America, EU, Australia, Saudi Arabia

Warranty: 2 years on fixture and wiring

14. Downloads: Downloads & Resources

Spec Sheet Setup Guide: 15. FAQs

FAQs: Will my landlord/HOA have a problem with this?

No — it’s a plug-in fixture, the same legal status as a floor lamp or table lamp. The only attachment to the wall is two small screws (about the size of a picture-hanging anchor); patching two holes on move-out takes 5 minutes. There’s no electrical modification to the unit, so no permits or landlord approval are required for installation.

What bulb works best?

E26 socket — any standard LED or Edison bulb up to 40W. For the visible-filament look that suits the open socket, use a vintage-style Edison LED (ST64, G80, or G125 globe shape, 2700K, 4–6W). For a softer ambient glow, use a frosted A19 or G45 LED. The test bulb included is a basic warm-white LED — works on arrival, swap to your preferred style anytime.

Is it dimmable?

The cord has an on/off push switch only. To dim: install a dimmable LED bulb plus a smart plug (Lutron Caséta or TP-Link Kasa) — the bulb dims through the app or schedule. No rewiring needed.

Where can I install it — height, location?

The bulb hangs about 6″ below the mount point, so mount the disk approximately 54″ above the floor for a standard bedside-reading height. For above-couch ambient lighting, mount 60″ above the seat. Distance to the wall outlet matters too — the 78.7″ cord gives ~6.5 ft of reach, including some slack. Indoor dry locations only (not bathrooms or kitchens above stovetops).

What’s the warranty?

16. Schema.org JSON-LD